M 25 C MARINE GENERATOR SET
The complete diesel generator set is notable for its ease of installation, reliable operation, ease of maintenance and good component accessibility. The basis is formed by the rigid base frame as a foundation of the engine and alternator with an integrated oil sump, large oil volume and universal equipment for both HFO and MDO operation. The M 25 C has a wide range of application providing power for the continuous generation of electricity where a high level of reliability is important. The power range of the M 25 C engine series as a generator unit varies from 2,140 to 3,560 kVA.
SPECIFICATIONS
Minimum Rating1669 kWe (2088 kVA)
Maximum Rating2877 kWe (3600 kVA)
Emissions/Fuel StrategyIMO II
generator set specifications
Minimum Rating1669 kWe (2088 kVA)
Maximum Rating2877 kWe (3600 kVA)
generator set configurations
Emissions/Fuel StrategyIMO II
engine specifications
Configuration6,8,9 Cylinder
Bore255 mm
Stroke400 mm
Swept Volume20.4 l/cyl.
generator set dimensions and weights dependent on generator type
Length8070 mm - 9516 mm (317.7 in - 374.6 in)
Width2479 mm - 2534 mm ( 97.6 in - 99.8 in)
Height3911 mm - 3963 mm (154.0 in - 156.0 in)
Weight43 t - 56 t (94799 lbs - 123459 lbs)
M 25 C STANDARD EQUIPMENT
- air inlet system
Air intake silencer / filter - control system
Load sharing unit (for multiple engine plant only)
Protection system
Serial link interface (MODbus / canbus)
Speed governor - cooling system
Electric cooling water preheater
HT cooling water pump (engine driven)
2-stage charge air cooler - exhaust system
Exhaust gas expansion joint
Exhaust gas insulated manifolds
Turbocharger at counter-flywheel end - fuel system
Fuel circulating pump (attached / for MDO/MGO only)
Fuel indicator filter
Fuel pressure valve (fitted / for MDO/MGO only) - instrumentation
Control push buttons and lamps
Emergency stop lever
Local control panel
Pressure and temperature indicator - lube system
Lube oil cooler (separate)
Lube oil pump (engine driven)
Lube oil self-cleaning filter
Pre-lubricating pump (electric driven / fitted on base frame)
Oil sump in base frame
Pressure regulating valve - mounting system
Flexible pipe connections
High flexible coupling
Resilient mounting on base frame - starting system
Electrical barring device
Starting air valve - general
Engine, flex. coupling and generator mounted on a common base frame
Flywheel cover
Lifting device (rental)
Torsional Vibration Calculation (TVC)
M 25 C OPTIONS
- air inlet system
Air inlet shut-off valve
Air intake transition piece
Expansion joint
Silencer / filter - control system
Air injection control (for better load request)
Electronic speed governor
Engine alarm system
Remote indicators (start air pressure, engine speed, etc.)
Starter for electric driven pumps
24 DC UPS - cooling system
CW piping for generator cooliing on base frame
CW piping for lubricating oil cooler on base frame
FW/SW plate cooler
HT cooling water pump (electric driven)
HT temperature control valve fitted on base frame
LT cooling water pump (electric driven)
Sea water cooling pump (electric driven)
Temperature control valve - exhaust system
Silencer (with or without spark arrester) - fuel system
Fuel oil cooler
HFO final preheater
HFO pressure regulating valve
HFO self-cleaning automatic filter
HFO supply and booster pumps (electric driven)
HFO treatment and supply modules
HFO viscosity control device
Mixing tank - lube system
Lube oil centrifuge
Lube oil cooler fitted on base frame
Lube oil pump (electrical driven)
Lube oil treatment and combined modules
Temperature control valve fitted on base frame - mounting system
Double resilient mounting (engine and base frame) - starting system
Starting air compressor
Starting air receiver - general
Engine PTO coupling
Generator customer supply
PTO shaft on counter-flywheel side